Emacs normally contains many keymaps; at any given time, just a few of them are active in that they participate in the interpretation of user input. These are the global keymap, the current buffer's local keymap, and the keymaps of any enabled minor modes.
The global keymap holds the bindings of keys that are defined
regardless of the current buffer, such as C-f. The variable
global-map holds this keymap, which is always active.
Each buffer may have another keymap, its local keymap, which may
contain new or overriding definitions for keys. The current buffer's
local keymap is always active except when overriding-local-map
overrides it. Text properties can specify an alternative local map for
certain parts of the buffer; see section Properties with Special Meanings.
Each minor mode can have a keymap; if it does, the keymap is active when the minor mode is enabled.
The variable overriding-local-map, if non-nil, specifies
another local keymap that overrides the buffer's local map and all the
minor mode keymaps.
All the active keymaps are used together to determine what command to execute when a key is entered. Emacs searches these maps one by one, in order of decreasing precedence, until it finds a binding in one of the maps. The procedure for searching a single keymap is called key lookup; see section Key Lookup.
Normally, Emacs first searches for the key in the minor mode maps, in
the order specified by minor-mode-map-alist; if they do not
supply a binding for the key, Emacs searches the local map; if that too
has no binding, Emacs then searches the global map. However, if
overriding-local-map is non-nil, Emacs searches that map
first, before the global map.
Since every buffer that uses the same major mode normally uses the
same local keymap, you can think of the keymap as local to the mode. A
change to the local keymap of a buffer (using local-set-key, for
example) is seen also in the other buffers that share that keymap.
The local keymaps that are used for Lisp mode and some other major
modes exist even if they have not yet been used. These local maps are
the values of variables such as lisp-mode-map. For most major
modes, which are less frequently used, the local keymap is constructed
only when the mode is used for the first time in a session.
The minibuffer has local keymaps, too; they contain various completion and exit commands. See section Introduction to Minibuffers.
Emacs has other keymaps that are used in a different way--translating
events within read-key-sequence. See section Translating Input Events.
See section Standard Keymaps, for a list of standard keymaps.
self-insert-command to all of the printing characters.
It is normal practice to change the bindings in the global map, but you should not assign this variable any value other than the keymap it starts out with.
global-map unless you change one or the
other.
(current-global-map)
=> (keymap [set-mark-command beginning-of-line ...
delete-backward-char])
nil
if it has none. In the following example, the keymap for the
`*scratch*' buffer (using Lisp Interaction mode) is a sparse keymap
in which the entry for ESC, ASCII code 27, is another sparse
keymap.
(current-local-map)
=> (keymap
(10 . eval-print-last-sexp)
(9 . lisp-indent-line)
(127 . backward-delete-char-untabify)
(27 keymap
(24 . eval-defun)
(17 . indent-sexp)))
nil.
It is very unusual to change the global keymap.
nil, then the buffer has no local
keymap. use-local-map returns nil. Most major mode
commands use this function.
(variable . keymap)
The keymap keymap is active whenever variable has a
non-nil value. Typically variable is the variable that
enables or disables a minor mode. See section Keymaps and Minor Modes.
Note that elements of minor-mode-map-alist do not have the same
structure as elements of minor-mode-alist. The map must be the
CDR of the element; a list with the map as the CADR will not
do. The CADR can be either a keymap (a list) or a symbol
whose function definition is a keymap.
When more than one minor mode keymap is active, their order of priority
is the order of minor-mode-map-alist. But you should design
minor modes so that they don't interfere with each other. If you do
this properly, the order will not matter.
See section Keymaps and Minor Modes, for more information about minor
modes. See also minor-mode-key-binding (see section Functions for Key Lookup).
minor-mode-map-alist: (variable
. keymap).
If a variable appears as an element of
minor-mode-overriding-map-alist, the map specified by that
element totally replaces any map specified for the same variable in
minor-mode-map-alist.
minor-mode-overriding-map-alist is automatically buffer-local in
all buffers.
nil, this variable holds a keymap to use instead of the
buffer's local keymap and instead of all the minor mode keymaps. This
keymap, if any, overrides all other maps that would have been active,
except for the current global map.
nil, this variable holds a keymap to use instead of
overriding-local-map, the buffer's local keymap and all the minor
mode keymaps.
This variable is always local to the current terminal and cannot be buffer-local. See section Multiple Displays. It is used to implement incremental search mode.
nil, the value of
overriding-local-map or overriding-terminal-local-map can
affect the display of the menu bar. The default value is nil, so
those map variables have no effect on the menu bar.
Note that these two map variables do affect the execution of key sequences entered using the menu bar, even if they do not affect the menu bar display. So if a menu bar key sequence comes in, you should clear the variables before looking up and executing that key sequence. Modes that use the variables would typically do this anyway; normally they respond to events that they do not handle by "unreading" them and exiting.
read-event. See section Special Events.
Go to the first, previous, next, last section, table of contents.