Time Conversion

These functions convert time values (lists of two or three integers) to strings or to calendrical information. There is also a function to convert calendrical information to a time value. You can get time values from the functions current-time (see section Time of Day) and file-attributes (see section Other Information about Files).

Many operating systems are limited to time values that contain 32 bits of information; these systems typically handle only the times from 1901-12-13 20:45:52 UTC through 2038-01-19 03:14:07 UTC. However, some operating systems have larger time values, and can represent times far in the past or future.

Time conversion functions always use the Gregorian calendar, even for dates before the Gregorian calendar was introduced. Year numbers count the number of years since the year 1 B.C., and do not skip zero as traditional Gregorian years do; for example, the year number -37 represents the Gregorian year 38 B.C.

Function: format-time-string format-string time

This function converts time to a string according to format-string. The argument format-string may contain `%'-sequences which say to substitute parts of the time. Here is a table of what the `%'-sequences mean:

`%a'

This stands for the abbreviated name of the day of week.

`%A'

This stands for the full name of the day of week.

`%b'

This stands for the abbreviated name of the month.

`%B'

This stands for the full name of the month.

`%c'

This is a synonym for `%x %X'.

`%C'

This has a locale-specific meaning. In the default locale (named C), it is equivalent to `%A, %B %e, %Y'.

`%d'

This stands for the day of month, zero-padded.

`%D'

This is a synonym for `%m/%d/%y'.

`%e'

This stands for the day of month, blank-padded.

`%h'

This is a synonym for `%b'.

`%H'

This stands for the hour (00-23).

`%I'

This stands for the hour (00-12).

`%j'

This stands for the day of the year (001-366).

`%k'

This stands for the hour (0-23), blank padded.

`%l'

This stands for the hour (1-12), blank padded.

`%m'

This stands for the month (01-12).

`%M'

This stands for the minute (00-59).

`%n'

This stands for a newline.

`%p'

This stands for `AM' or `PM', as appropriate.

`%r'

This is a synonym for `%I:%M:%S %p'.

`%R'

This is a synonym for `%H:%M'.

`%S'

This stands for the seconds (00-60).

`%t'

This stands for a tab character.

`%T'

This is a synonym for `%H:%M:%S'.

`%U'

This stands for the week of the year (01-52), assuming that weeks start on Sunday.

`%w'

This stands for the numeric day of week (0-6). Sunday is day 0.

`%W'

This stands for the week of the year (01-52), assuming that weeks start on Monday.

`%x'

This has a locale-specific meaning. In the default locale (named `C'), it is equivalent to `%D'.

`%X'

This has a locale-specific meaning. In the default locale (named `C'), it is equivalent to `%T'.

`%y'

This stands for the year without century (00-99).

`%Y'

This stands for the year with century.

`%Z'

This stands for the time zone abbreviation.

You can also specify the field width and type of padding for any of these `%'-sequences. This works as in printf: you write the field width as digits in the middle of a `%'-sequences. If you start the field width with `0', it means to pad with zeros. If you start the field width with `_', it means to pad with spaces.

For example, `%S' specifies the number of seconds since the minute; `%03S' means to pad this with zeros to 3 positions, `%_3S' to pad with spaces to 3 positions. Plain `%3S' pads with zeros, because that is how `%S' normally pads to two positions.

Function: decode-time time

This function converts a time value into calendrical information. The return value is a list of nine elements, as follows:

(seconds minutes hour day month year dow dst zone)

Here is what the elements mean:

sec

The number of seconds past the minute, as an integer between 0 and 59.

minute

The number of minutes past the hour, as an integer between 0 and 59.

hour

The hour of the day, as an integer between 0 and 23.

day

The day of the month, as an integer between 1 and 31.

month

The month of the year, as an integer between 1 and 12.

year

The year, an integer typically greater than 1900.

dow

The day of week, as an integer between 0 and 6, where 0 stands for Sunday.

dst

t if daylight savings time is effect, otherwise nil.

zone

An integer indicating the time zone, as the number of seconds east of Greenwich.

Common Lisp Note: Common Lisp has different meanings for dow and zone.

Function: encode-time seconds minutes hour day month year &optional ...zone

This function is the inverse of decode-time. It converts seven items of calendrical data into a time value. For the meanings of the arguments, see the table above under decode-time.

Year numbers less than 100 are treated just like other year numbers. If you want them to stand for years above 1900, you must alter them yourself before you call encode-time.

The optional argument zone defaults to the current time zone and its daylight savings time rules. If specified, it can be either a list (as you would get from current-time-zone), a string as in the TZ environment variable, or an integer (as you would get from decode-time). The specified zone is used without any further alteration for daylight savings time.

If you pass more than seven arguments to encode-time, the first six are used as seconds through year, the last argument is used as zone, and the arguments in between are ignored. This feature makes it possible to use the elements of a list returned by decode-time as the arguments to encode-time, like this:

(apply 'encode-time (decode-time ...))

You can perform simple date arithmetic by using out-of-range values for the sec, minute, hour, day, and month arguments; for example, day 0 means the day preceding the given month.

The operating system puts limits on the range of possible time values; if you try to encode a time that is out of range, an error results.

Go to the first, previous, next, last section, table of contents.