The usual way to invoke Emacs is with the shell command `emacs'. Emacs clears the screen and then displays an initial help message and copyright notice. Some operating systems discard all type-ahead when Emacs starts up; they give Emacs no way to prevent this. Therefore, it is advisable to wait until Emacs clears the screen before typing your first editing command.
If you run Emacs from a shell window under the X Window System, run it in the background with `emacs&'. This way, Emacs does not tie up the shell window, so you can use that to run other shell commands while Emacs operates its own X windows. You can begin typing Emacs commands as soon as you direct your keyboard input to the Emacs frame.
When Emacs starts up, it makes a buffer named `*scratch*'.
That's the buffer you start out in. The `*scratch*' buffer uses Lisp
Interaction mode; you can use it to type Lisp expressions and evaluate
them, or you can ignore that capability and simply doodle. (You can
specify a different major mode for this buffer by setting the variable
initial-major-mode
in your init file. See section The Init File, `~/.emacs'.)
It is possible to specify files to be visited, Lisp files to be loaded, and functions to be called, by giving Emacs arguments in the shell command line. See section Command Line Arguments. But we don't recommend doing this. The feature exists mainly for compatibility with other editors.
Many other editors are designed to be started afresh each time you want to edit. You edit one file and then exit the editor. The next time you want to edit either another file or the same one, you must run the editor again. With these editors, it makes sense to use a command-line argument to say which file to edit.
But starting a new Emacs each time you want to edit a different file does not make sense. For one thing, this would be annoyingly slow. For another, this would fail to take advantage of Emacs's ability to visit more than one file in a single editing session. And it would lose the other accumulated context, such as registers, undo history, and the mark ring.
The recommended way to use GNU Emacs is to start it only once, just after you log in, and do all your editing in the same Emacs session. Each time you want to edit a different file, you visit it with the existing Emacs, which eventually comes to have many files in it ready for editing. Usually you do not kill the Emacs until you are about to log out. See section File Handling, for more information on visiting more than one file.
There are two commands for exiting Emacs because there are two kinds of exiting: suspending Emacs and killing Emacs.
Suspending means stopping Emacs temporarily and returning control to its parent process (usually a shell), allowing you to resume editing later in the same Emacs job, with the same buffers, same kill ring, same undo history, and so on. This is the usual way to exit.
Killing Emacs means destroying the Emacs job. You can run Emacs again later, but you will get a fresh Emacs; there is no way to resume the same editing session after it has been killed.
suspend-emacs
) or iconify a frame
(iconify-or-deiconify-frame
).
save-buffers-kill-emacs
).
To suspend Emacs, type C-z (suspend-emacs
). This takes
you back to the shell from which you invoked Emacs. You can resume
Emacs with the shell command `%emacs' in most common shells.
On systems that do not support suspending programs, C-z starts an inferior shell that communicates directly with the terminal. Emacs waits until you exit the subshell. (The way to do that is probably with C-d or `exit', but it depends on which shell you use.) The only way on these systems to get back to the shell from which Emacs was run (to log out, for example) is to kill Emacs.
Suspending also fails if you run Emacs under a shell that doesn't
support suspending programs, even if the system itself does support it.
In such a case, you can set the variable cannot-suspend
to a
non-nil
value to force C-z to start an inferior shell.
(One might also describe Emacs's parent shell as "inferior" for
failing to support job control properly, but that is a matter of taste.)
When Emacs communicates directly with an X server and creates its own
dedicated X windows, C-z has a different meaning. Suspending an
applications that uses its own X windows is not meaningful or useful.
Instead, C-z runs the command iconify-or-deiconify-frame
,
which temporarily closes up the selected Emacs frame (see section Frames and X Windows).
The way to get back to a shell window is with the window manager.
To kill Emacs, type C-x C-c (save-buffers-kill-emacs
). A
two-character key is used for this to make it harder to type. This
command first offers to save any modified file-visiting buffers. If you
do not save them all, it asks for reconfirmation with yes before
killing Emacs, since any changes not saved will be lost forever. Also,
if any subprocesses are still running, C-x C-c asks for
confirmation about them, since killing Emacs will kill the subprocesses
immediately.
There is no way to restart an Emacs session once you have killed it. You can, however, arrange for Emacs to record certain session information, such as which files are visited, when you kill it, so that the next time you restart Emacs it will try to visit the same files and so on. See section Saving Emacs Sessions.
The operating system usually listens for certain special characters whose meaning is to kill or suspend the program you are running. This operating system feature is turned off while you are in Emacs. The meanings of C-z and C-x C-c as keys in Emacs were inspired by the use of C-z and C-c on several operating systems as the characters for stopping or killing a program, but that is their only relationship with the operating system. You can customize these keys to run any commands of your choice (see section Keymaps).
Go to the first, previous, next, last section, table of contents.