Go to the first, previous, next, last section, table of contents.

Checking and Correcting Spelling

This section describes the commands to check the spelling of a single word or of a portion of a buffer. These commands work with the spelling checker program Ispell, which is not part of Emacs.

M-x flyspell-mode

Enable Flyspell mode, which highlights all misspelled words.

M-$

Check and correct spelling of the word at point (ispell-word).

M-TAB

Complete the word before point based on the spelling dictionary (ispell-complete-word).

M-x ispell-buffer

Check and correct spelling of each word in the buffer.

M-x ispell-region

Check and correct spelling of each word in the region.

M-x ispell-message

Check and correct spelling of each word in a draft mail message, excluding cited material.

M-x ispell-change-dictionary RET dict RET

Restart the Ispell process, using dict as the dictionary.

M-x ispell-kill-ispell

Kill the Ispell subprocess.

Flyspell mode is a fully-automatic way to check spelling as you edit in Emacs. It operates by checking words as you change or insert them. When it finds a word that it does not recognize, it highlights that word. This does not interfere with your editing, but when you see the highlighted word, you can move to it and fix it. Type M-x flyspell-mode to enable or disable this mode in the current buffer.

When Flyspell mode highlights a word as misspelled, you can click on it with Mouse-2 to display a menu of possible corrections and actions. You can also correct the word by editing it manually in any way you like.

The other Emacs spell-checking features check or look up words when you give an explicit command to do so. Checking all or part of the buffer is useful when you have text that was written outside of this Emacs session and might contain any number of misspellings.

To check the spelling of the word around or next to point, and optionally correct it as well, use the command M-$ (ispell-word). If the word is not correct, the command offers you various alternatives for what to do about it.

To check the entire current buffer, use M-x ispell-buffer. Use M-x ispell-region to check just the current region. To check spelling in an email message you are writing, use M-x ispell-message; that checks the whole buffer, but does not check material that is indented or appears to be cited from other messages.

Each time these commands encounter an incorrect word, they ask you what to do. They display a list of alternatives, usually including several "near-misses"---words that are close to the word being checked. Then you must type a character. Here are the valid responses:

SPC

Skip this word--continue to consider it incorrect, but don't change it here.

r new RET

Replace the word (just this time) with new.

R new RET

Replace the word with new, and do a query-replace so you can replace it elsewhere in the buffer if you wish.

digit

Replace the word (just this time) with one of the displayed near-misses. Each near-miss is listed with a digit; type that digit to select it.

a

Accept the incorrect word--treat it as correct, but only in this editing session.

A

Accept the incorrect word--treat it as correct, but only in this editing session and for this buffer.

i

Insert this word in your private dictionary file so that Ispell will consider it correct it from now on, even in future sessions.

u

Insert the lower-case version of this word in your private dictionary file.

m

Like i, but you can also specify dictionary completion information.

l word RET

Look in the dictionary for words that match word. These words become the new list of "near-misses"; you can select one of them to replace with by typing a digit. You can use `*' in word as a wildcard.

C-g

Quit interactive spell checking. You can restart it again afterward with C-u M-$.

X

Same as C-g.

x

Quit interactive spell checking and move point back to where it was when you started spell checking.

q

Quit interactive spell checking and kill the Ispell subprocess.

C-l

Refresh the screen.

C-z

This key has its normal command meaning (suspend Emacs or iconify this frame).

The command ispell-complete-word, which is bound to the key M-TAB in Text mode and related modes, shows a list of completions based on spelling correction. Insert the beginning of a word, and then type M-TAB; the command displays a completion list window. To choose one of the completions listed, click Mouse-2 on it, or move the cursor there in the completions window and type RET. See section Text Mode.

Once started, the Ispell subprocess continues to run (waiting for something to do), so that subsequent spell checking commands complete more quickly. If you want to get rid of the Ispell process, use M-x ispell-kill-ispell. This is not usually necessary, since the process uses no time except when you do spelling correction.

Ispell uses two dictionaries: the standard dictionary and your private dictionary. The variable ispell-dictionary specifies the file name of the standard dictionary to use. A value of nil says to use the default dictionary. The command M-x ispell-change-dictionary sets this variable and then restarts the Ispell subprocess, so that it will use a different dictionary.

Go to the first, previous, next, last section, table of contents.